Steel City Tool Works 40200H 13-Inch Planer with Spiral Cutterhead by Steel City Tool Works
List Price : $1,079.99
Price : $614.98
Warranty: 5 Years.Feed Rate: 26 FPM.Max. Width of Stock: 13-Inch - Min. Thickness of Stock: 1/8-Inch.Cutter Head Speed: 9000 RPM.Motor: Universal 15 Amp, 120V, 60Hz...
The Steel City Tool Works 40200H 13-Inch Planer with Spiral Cutterhead for Sale it's best Warranty: 5 Years.Feed Rate: 26 FPM.Max. Width of Stock: 13-Inch - Min. Thickness of Stock: 1/8-Inch.Cutter Head Speed: 9000 RPM.Motor: Universal 15 Amp, 120V, 60Hz...
Read more Steel City Tool Works 40200H 13-Inch Planer with Spiral Cutterhead
Steel City Tool Works 40200H 13-Inch Planer with Spiral Cutterhead Feature
Customer Reviews
four.2 Out Of 5 Stars (6 Customer Reviews)Reviews for Steel City Tool Works four0200H 13-Inch Planer with Spiral Cutterhead (Tools & Home Improvement) Good: helical cutting head at this price level! 13" width capability, 6" top capability down to 1/8" inch, quick setup for repeat thickness runs, surprisingly quiet during full load, superb chip extraction, primarily prepared to make use of out of the field with little if any adjustment wanted to parallel the improve tables (they fold upwards when not in use leading to very small foot print when unit is stored away), enhance desks are long, go aways a good end, 5 yr guarantee.
Bad: single feed pace is merely too fast for some laborious woods leading to some minor tear-out; rotating the board for every other move lend a hands however a slower feed pace would eliminate this problem solely.
Overall: 13" helical cutter in a solidly built desktop at an incredible value; having a look ahead to a few 12 monthss of service.
Reviews for Steel City Tool Works 40200H 13-Inch Planer with Spiral Cutterhead (Tools & Home Improvement) I have had this planer for a number of months and put quite loads of hickory, exhausting maple, delicate maple, and purple oak via it. This is and improve for an older Dewalt 2 blade cutter head. I upgraded because I was as soon as tired of having to get blades sharpened often and bored with dealing with tearout from the coarser grain woodens.
The planer got here shipped within the in is own box without a issues. Once out of the field it could be very necessary smooth off some grease from desk of the planer, but nothing to main. After the you attach the four" dust gatheror port you're ready to go.
I did have to regulate the extent of the infeed and outfeed table to do away with snipe, but nonetheless have some on the primary and last couple inches of the board. I be conscious of some individuals to find snipe to be an enormous deal, I plan for it and simply cut off the ends.
The very first thing you no lengthyerice whilst you first begin using it's how quiet it's. This does not topic to me a lot as a result of I have a loud dust accumulateor and I always use hearing safety. But it is significantly quieter then straight blade planers. The phase that I am dissatisfied with is you continue to get a fair quantity scallops and tearout from the coarser grain woodens. I was underneath the impression that the spiral head was once supposed to no longericeably lower tearout or put off it.
Reviews for Steel City Tool Works 40200H 13-Inch Planer with Spiral Cutterhead (Tools & Home Improvement) First, I have no idea concerning the durability/longevity of this product, but I will say that I suppose in the end this shall be a computer that closings for me. As many have pointed out, this is basically a Ridgid 13" planer with a spiral chopping head. However, the perimeters are all steel and general the fabrics seem to be of a higher specification/quality than the Ridgid variations. I sparsely researched this desktop and skim a lot of reviews before I at remaining bit the bullet and bought this unit. I'd believeed the Delta and Dewalt portable editions in the same value vary ($600). The up to date price drop on this Steel City unit truly assisted me make the ultimate resolution in addition to the spiral chopping head. Many have commented about the "grease" around the cutter head and on one timberworking discussion board somebody carped on ceaselessly about using Q-tips to clean the cutter head. I idea that appeared a bit of ordinary, so I was ready to look for myself as soon as the unit arrived. I removed the protecting shroud around the cutter head and sure, there is a vital amount of grease on the top. In my opinion this is Cosmoline or another rust inhibitor. Douse the head with some brake smoother or do what I did: take hold of some smooth lumber (like pine) and run it thru except you accumulate a Shop Vac or two filled with shavings. This coating in point of fact is not as unhealthy as one of the vital assessments. If you consider the entire bare metal and surface space that's exposed on this spiral cutter head, the rust inhibitor is important. The atmosphere within a shipping container from China to the U.S. is a corrosive one for equipment. I'm glad that Steel City's in another country supplier is taking this precaution.
